{"id":104,"date":"2011-08-01T22:36:22","date_gmt":"2011-08-02T04:36:22","guid":{"rendered":"http:\/\/beta.solidshandlingtech.com\/?p=104"},"modified":"2017-11-09T21:51:58","modified_gmt":"2017-11-09T21:51:58","slug":"handle-cohesive-products-with-live-bottom-screws","status":"publish","type":"post","link":"https:\/\/solidshandlingtech.com\/?p=104","title":{"rendered":"Handle Cohesive Products with Live Bottom Screws"},"content":{"rendered":"

Handle Cohesive Products with Live Bottom Screws<\/strong><\/span>
\nby Joseph Marinelli, Solids Handling Technologies<\/span><\/span><\/h2>\n
\"\"Those of you have read my column over the years know that I am a big proponent of screw feeders. Screws are reliable, robust and can handle a range of products, but most importantly will maintain a mass flow pattern if designed properly. Most bulk solids require a mass flow pattern as funnel flow is susceptible to ratholing, erratic flow, flooding, segregation, etc. As I have always stated, in order to evaluate whether a solid is going to flow properly, you need to measure its flow properties. Once its flow properties are determined, reliable bin and feeder designs can be developed.<\/span><\/h5>\n
Some materials are extremely cohesive and as such require large openings to prevent arching. Materials that come to mind are synthetic gypsum (sometimes referred to as FGD gypsum, flue gas desulferized gypsum), sludge, wet, heavy solids, etc. Mass flow is definitely required to maintain reliable flow. The feeder design is critical to maintaining a mass flow pattern. If the feeder creates a preferential flow channel, the material will flow in funnel flow and destroy the required mass flow pattern.<\/span><\/h5>\n
One approach that is commonly used is live bottom screws. As the name implies, the bottom (outlet) is fully live. Material discharges over the entire cross-sectional area of rather large outlets to maintain mass flow.<\/span><\/h5>\n
Assuming that your hopper is designed to give you reliable mass flow, a live bottom screw feeder must be capable of maintaining the mass flow pattern and withdraw material uniformly over the entire outlet’s cross-sectional area. The key to this approach is to ensure that the feeder\u00a0increases<\/span>in capacity in the discharge direction.<\/span><\/h5>\n
Take, for example, the constant pitch, constant diameter screw shown here:<\/span><\/h5>\n
\"\"<\/span><\/h5>\n
The material will be withdrawn preferentially from the back of the screw. The constant pitch flights do not allow any increase in capacity in the direction of feed. Therefore, the last flight fills with material and there is no more capacity to take material over the entire outlet length. Any modifications that you made to your hopper to ensure mass flow are now rendered useless. The improperly designed screw feeder creates a preferential flow channel that enforces a funnel flow pattern with its resulting problems of ratholing, erratic flow, flooding, segregation, etc.<\/span><\/h5>\n
The design shown here is a combination of conical shaft and increasing pitch to maintain
\nmass flow:<\/span><\/h5>\n
\"\"<\/span><\/h5>\n
You might notice the following:
\n1. Trough Shape:\u00a0 There is U-shaped trough to contain the screw. Vee-shaped troughs will not work because material usually only feeds directly above the screw diameter. A Vee-shaped trough will create stagnant material and destroy your mass flow pattern.
\n2. Hanger Bearings:\u00a0 There are no hanger bearings to support the screw; therefore, the screw shaft has to be sized to withstand deflection. Hanger bearings will interfere with the full screw trough. Material will back up into the hopper, affecting flow. Your hanger bearings will also wear out quickly.
\n3. Finishes:\u00a0 The screw flights should be smooth while the screw trough (walls) should be rough. If they are both smooth, the material will simply spin in the trough and not convey.
\n4. Speed:\u00a0 The screw speed should be kept between 3 and 40 rpm. The screw speed should be 3 rpm on the low side to minimize speed reducer size and 40 rpm on the high side to maintain screw efficiency.
\n5. Clearances:\u00a0 There is \u0405\u201d clearance between the screw and screw trough.<\/span><\/h5>\n
Remember to always:
\n\u2022 Measure your material\u2019s flow properties.
\n\u2022 Design your bin for the correct flow pattern.
\n\u2022 Design your live bottom screw feeder properly, to ensure reliable flow.<\/span><\/h5>\n
For more information contact our author:<\/span><\/h5>\n

Joe Marinelli
\nSolids Handling Technologies, Inc.
\n1631 Caille Court
\nFort Mill, SC 29708
\nTelephone: 803-802-5527
\nFax: 803-802-0193
\nEmail:\u00a0joe@solidshandlingtech.com<\/a><\/span>
\n Web site:\u00a0https:\/\/solidshandlingtech.com\/<\/a><\/span><\/p>\n

Guest articles for the Ask Joe! Column are always welcome, for more information please contact Joe Marinelli directly at his email address:\u00a0\u00a0joe@solidshandlingtech.com<\/a>.<\/span><\/h5>\n","protected":false},"excerpt":{"rendered":"

Handle Cohesive Products with Live Bottom Screws by Joseph Marinelli, Solids Handling Technologies Those of you have read my column over the years know that I am a big proponent of screw feeders. Screws are reliable, robust and can handle a range of products, but most importantly will maintain a mass flow pattern if designed […]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_monsterinsights_skip_tracking":false,"footnotes":""},"categories":[2],"tags":[4],"class_list":["post-104","post","type-post","status-publish","format-standard","hentry","category-articles","tag-feeders"],"_links":{"self":[{"href":"https:\/\/solidshandlingtech.com\/index.php?rest_route=\/wp\/v2\/posts\/104","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/solidshandlingtech.com\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/solidshandlingtech.com\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/solidshandlingtech.com\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/solidshandlingtech.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=104"}],"version-history":[{"count":4,"href":"https:\/\/solidshandlingtech.com\/index.php?rest_route=\/wp\/v2\/posts\/104\/revisions"}],"predecessor-version":[{"id":437,"href":"https:\/\/solidshandlingtech.com\/index.php?rest_route=\/wp\/v2\/posts\/104\/revisions\/437"}],"wp:attachment":[{"href":"https:\/\/solidshandlingtech.com\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=104"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/solidshandlingtech.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=104"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/solidshandlingtech.com\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=104"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}